The ice manufacturer line to my fridge presently does not have any shutoff valve and I also’d love to include one but i can not find out just what size the connector is

we bought a 1/4 inch valve considering that the ice manufacturer connector we have actually says 1/4 FCM it did not fit on it but. It seems a lot more like 1/8 inches, however a https://find-a-bride.net/ 1/8 inches valve does not fit either, though it is quite near. Where may I find information regarding water pipeline sizes, there should be some standard?

The copper water line i will be linking it to has got the precise exact same dimension as the refrigerator.

MODIFY:

Okay I was thinking that looking the net for 1/4″ OD Valve Male Female would get me personally the things I require but i will be getting no total outcomes thus I’ve reopened issue! Can anybody offer me personally an internet url to a item which will fit? I have added a photograph of this present connection where i would ike to include the valve. Many Many Thanks!

3 Responses 3

You will find various requirements to pipelines and threads. Your problem is you are making an effort to mix two various standards that are threaded.

The ball valve which you associated with has nationwide pipeline threads (NPT). NPT are tapered also it is the fact that taper that produces the seal from a female and male joint. No washers are needed.

What’s shown in your picture is compression fixtures that have a right or operating thread. The seal is created by either a ferrule or a plastic washer.

The connection between the copper tube and the supply hose has been made as follows in your case

1/4″ Copper Tube > 1/4″ Compression by 1/4″ Compression Coupling > 1/4″ Supply Hose

The seal on the copper pipe is created with a ferrule that is situated underneath the nut. Because the nut is tightened, the ferrule is compressed amongst the coupling while the pipeline.

The seal on the supply hose part is created by way of a rubber washer that will be often integral the the nut associated with supply hose. (The compression coupling will have include two pea pea pea pea nuts, certainly one of which includes been discarded given that supply hose has one integrated.)

Therefore, to respond to your concern, you simply require a 1/4″ compression x 1/4″ compression valve that may change the coupling that is current. Let me reveal a hyperlink to this type of valve.

Do the paperwork is had by you that was included with the refrigerator? It will show the ice maker install and say the size maybe associated with valve. We have constantly seen that it is 1/4″.

Where is the water line tapped from? Often it comes down a 1/2″ copper pipeline. You can place your valve from the copper pipeline part.

EDIT: web Page 33 of this installation manual states that the water supply pipe is 1/4″ OD. You want a 1/4″ valve. Be certain there are not any burrs regarding the copper tubing after you cut it. Often you’ll want to register the sides. In the event that pipeline cutter just isn’t razor- razor- sharp it could mushroom the ends which will ensure it is appear it is maybe perhaps not the right diameter.

When you yourself have more hours and cash, the advisable thing is to run either a 1/2 inches copper line or perhaps a 1/2 galvanized line into the straight back of the fridge having a 1/4 inches connection onto it, ideally set into the wall surface in synthetic package. An alternative cheaper method is always to run a 1/4 inches line through the 1/4 inches connection at your double shut off valve under your drain. Nonetheless, the copper line is really a difficult line and it gets crimped particularly when you or somebody else is careless in going the refrigerator around to completely clean or any.

Utilizing two crescent wrenches, this is what to accomplish in the event that you currently have a copper that is hard to your straight straight straight straight back without a shut down valve anywhere in web site. You can purchase a kit with the right components you need, 1/4 inches connectors having a 6 base, 1/4 inches supply hose, who has the 1/4 pea pea nuts on both ends. Carefully get it done yourself or get a plumber to slice the copper line by having a copper pipeline cutter, a good cut that is clean a few of ins this part of in which the line is released of wall surface or case (provided that it is not crimped, you are ok to cut it).

Place the free 1/4 inches nut on backwards regarding the pipeline, and so the nut covers the ferrel tucked in during the side of the final end for the pipeline, then, screw regarding the 1/4 inches connector/adjuster into it, because of the 1/4 inches threads towards the 1/4 inches nut in the hose, and tighten up, snug, never ever overbearing, ever with any plumbing system. Then link one other end of hose/nut towards the end that is threaded the ice box at the end, snug! Remember! But, a good thing to complete whenever you are linking a line to either a tap or fridge or in any case could be, it on to clear the line of air and grub, because who knows how long it’s been sitting before you put that last connection on the refrigerator, put that end in a big bucket and turn. Plus, if you have atmosphere when you look at the lines, which is a nother that is whole, believe me you will not want! Have the atmosphere away! Can be done all this your self too! Do not forget to always check every thing for leaks! Best of luck! Now get commemorate you simply spared your self $150.